Items:
0
Total:
$0
View Cart

Shopping Cart

0 item(s) in your shopping cart

ITEMS
QTY
PRICE
Total
 
[ITEM_NAME]
View/Hide options
This item will Autoship every [recurring_frequency]
[ITEM_PRICE]
[ITEM_SUBTOTAL]
Subtotal: $0
Your cart is empty.

Springtime Eclipse Flat Leather Bracelet

Springtime Eclipse Flat Leather Bracelet

Want to make this Design Idea? See products and other information below.

Supply List:

  • 7 inches Leather Flat 20mm - Apple Green
  • 7 inches Gorgeous Goat Leather Flat 10mm - Aztec
  • 1 Leather Cord Flat 20mm Clasp Magnetic Tin Punch - Antique Silver
  • 2 C-Koop Copper Enamel Rivetable / Stackable Disc 13mm Black
  • 1 C-Koop Copper Enamel Rivetable / Stackable Disc 19mm Black
  • 7 6mm Rubber O-Rings BAG of 25 - White
  • 2 12mm Rubber O-Ring Spacer - Black
  • 7 TierraCast Snap Rivets 4mm Bag of 10 - Silver Plate
  • Super New Glue

    Finished Length: 7 1/2 inches

    Level of Difficulty: Intermediate

    Tools: Leather Punch, Nail Setter, Bench Block, Hammer, Leather Cutter
  • Designer Tip: Glue Goat leather to center of 20mm flat leather using 4-5 drops of glue at approximately 1 intervals (this will keep the goat leather positioned as you punch holes and rivet the embellishments). Find and mark center of leather; mark 3 additional spots at intervals from center. Punch holes through both thicknesses of leather as marked using the 5/64 (smallest) setting of the leather punch. Use a small amount of glue to position a white O ring in each C-Koop disk. Use the bench block and nail setter to rivet the disks and white O rings to the leather. Check the bracelet size and trim 20mm leather if necessary (equally on both sides to keep the disks centered) before gluing the 20mm leather into the clasp. Add the 12mm O-rings to each end. With clasp fastened, trim goat leather so it is flush with the clasp. Use additional glue if needed to make sure ends are glued to the 20mm leather. Position O-rings so they cover the end of the goat leather and are flush with the clasp.

    Helpful Video Tutorial:Click here to Watch How to Use a Nail Setter to Make Jewelry Video Tutorial

    To add items to your cart, fill in the desired quantity at the top or bottom of the page to add all selected items to your shopping cart.

    Products (Total Items: 4)
    Sort by:
    Select Quantities
    C-Koop Copper Enamel Rivetable / Stackable Disc 13mm - Black
    C-Koop Copper Enamel Rivetable / Stackable Disc 13mm - Black
    Part #: CU228-1995
    13x3mm
    Hole Size: 2.4mm
    Sold Individually
    Use with 4mm TierraCast Rivets
    Your Price: $4.80
    11 In Stock.
    Enter
    Quantity
    Average Rating0 Review(s)
    C-Koop Copper Enamel Rivetable / Stackable Disc 19mm - Black
    C-Koop Copper Enamel Rivetable / Stackable Disc 19mm - Black
    Part #: D104D-1995
    19x5mm
    Hole Size: 2.4mm
    Sold Individually
    Use with 4mm TierraCast Rivets
    Your Price: $7.45
    9 In Stock.
    Enter
    Quantity
    Average Rating0 Review(s)
    Nail Setter 2/32
    Nail Setter 2/32"
    Part #: NAIL-2
    NAIL-2 - Use this tool to set TierraCast 6mm Snap Rivets on C-Koop Enamel Rivetables and Stackables
    Length: 4 inches Diameter: 2/32 inch
    Sold Individually
    Made out of Stainless Steel
    Your Price: $6.55
    6 In Stock.
    Enter
    Quantity
    Average Rating0 Review(s)
    !Cutter Leather Black
    !Cutter Leather Black
    Part #: RZ-CUTTER
    RZ-CUTTER - Used to cut ALL Leather
    Click here for Replacement Blades - RZ-RBLD
    Sold Individually
    Your Price: $13.25
    0 In Stock
    Enter
    Quantity
    Average Rating3 Review(s)
    Select Quantities