View Cart

Shopping Cart

0 item(s) in your shopping cart

View/Hide options
This item will Autoship every [recurring_frequency]
Subtotal: $0
Your cart is empty.

Braided Band 20mm Flat Leather Bracelet

Braided Band 20mm Flat Leather Bracelet

Want to make this Design Idea?

You can quickly add all the required items by clicking the SELECT ALL button below, ENTERING required quantities like # of INCHES of Leather, UNCHECKING any unwanted items. Then go to bottom of page and click ADD TO CART.

Supply List:

  • 8 inches Braided Bonded 20mm Flat Leather Cord Beige
  • 8 inches Arizona 5mm Flat Leather Cord - Black
  • 1 5mm Candy Dots Flat Leather Cord Slider - Antique Silver
  • 6 TierraCast Snap Rivets 6mm - Silver Plated
  • 1 20mm Scales Flat Leather Cord Magnetic Clasp - Antique Silver
  • Super New Glue

    Finished Length: 8 1/2 inches

    Time to Make: Under 2 hours

    Level of Difficulty: Intermediate

    Tools: Leather Cutter or Flush Cutters, Leather Punch, 6mm Rivet Setter, Bench Block, Hammer

    Designer Tip: Mark and, using the smallest (5/32 inch) setting on the leather punch, punch holes in the Arizona leather from the end of the Arizona leather as follows: inch, 1 inch, 3 inches, 5 inches, 6 inches, and 7 inches. Add the slide to the 5mm leather and center between the two middle holes. Lay the 5mm leather over the 20mm leather and curve the leather. Starting from the middle, rivet the 5mm leather to the 20mm leather (the rivets will just poke through braided leather; it is not necessary to punch holes). Be sure to continue to curve the 20mm leather when determining where to set the remaining rivets. Check the bracelet size and trim the 20 mm leather on both sides before gluing it into the clasp. NOTE: the braid will quickly start to unravel when the tape is removed so work one side at a time. Close the bracelet; trim the ends of the Arizona leather flush with the clasp and glue to the 20mm leather.
  • Helpful Video Tutorial:Click here to Watch How to Size and Glue Leather Bracelets and Click here to Watch Leather Punching and Riveting Basics for Making Leather Bracelets

    Products (Total Items: 3)
    Sort by:
    Select Quantities
    Arizona 5mm Flat Leather Cord - Black - per inch
    Arizona 5mm Flat Leather Cord - Black - per inch
    Part #: 5AF-15
    5AF-15 - 5x1.5mm (sizes do vary slightly)
    Made in the European Union of genuine cowhide leather wrapped around a cotton core (there
    Sold by the Inch
    This leather has a soft, suede-like finish. It is more matte than the other flat leathers.
    It is made of a sheet of leather wrapped around a cotton core, so there is a seam on the underside of the leather.
    Glue ends with super glue designed for leather and metal.
    Your Price: $0.40
    4 In Stock.
    Average Rating0 Review(s)
    !Cutter Leather Black
    !Cutter Leather Black
    Part #: RZ-CUTTER
    RZ-CUTTER - Used to cut ALL Leather
    Click here for Replacement Blades - RZ-RBLD
    Sold Individually
    Your Price: $13.25
    0 In Stock
    Average Rating3 Review(s)
    Super New Glue
    Super New Glue
    Part #: glue-sng
    Sold in a 3 gram bottle. This glue sets in seconds. One drop bonds approximately one square inch of leather, rubber, metal, glass, ceramics, porcelain and plastic.
    Your Price: $4.00
    0 In Stock
    Average Rating0 Review(s)
    Select Quantities