Items:
0
Total:
$0
View Cart

Shopping Cart

0 item(s) in your shopping cart

ITEMS
QTY
PRICE
Total
 
[ITEM_NAME]
View/Hide options
This item will Autoship every [recurring_frequency]
[ITEM_PRICE]
[ITEM_SUBTOTAL]
Subtotal: $0
Your cart is empty.

20mm Flat Leather Cord Glue-In Metal Cuffs

20mm Flat Leather Cord Glue-In Metal Cuffs

Make cool custom Bracelets with our 20mm Glue-In Cuffs. They are adjustable and will fit most wrist sizes. Designing them is simple - just pick 7 inches of 20mm Flat Cord or 13 inches of 10mm Leather cut into two 6 1/2 inch lengths or 26 inches of 5mm Leather cut into four 6 1/2 inch lengths and follow the instructions listed below. Click here to see all 20mm, 10mm and 5mm Flat Cord Opportunities

To add items to your cart, fill in the desired quantity at the top or bottom of the page to add all selected items to your shopping cart.
Products (Total Items: 4)
Sort by:
Select Quantities
20mm Glue-In Cuff Flat Leather Cord per 5 pieces - Gunmetal
20mm Glue-In Cuff Flat Leather Cord per 5 pieces - Gunmetal
24.5x3mm
OD: 6 3/4 inches - start with 7 inch piece of cord and trim
Adjustable - will fit most wrist sizes
sold per bag
Brass Base Plated with gunmetal color
Blank Base to glue in 20mm flat cord
Designer Tip: Each bangle takes one bracelet blank and 6 1/2 inches of 20mm leather or 13 inches of 10mm Leather cut into two 6 1/2 inch lengths or 26 inches of 5mm Leather cut into four 6 1/2 inch lengths. The bracelet blanks have rounded corners and the ends are at a slight angle. Using sharp scissors or flush cutters, trim one end of the leather to fit the bangle. Glue the end in with Super New Glue and use tape or wire to hold the leather in place while drying. Spread a small amount of E-6000 on the bracelet blank starting from the glued portion to about inch away from the other end. Press leather in place and trim other end to fit in bangle. Apply Super New Glue to the end of bangle and press leather in place, again using tape of wire to hold the leather while the glue is drying. A nail file can be used to smooth the rounded corners if desired. If the Super New Glue does not hold, allow it to dry completely and reapply. The rationale for using the E-6000 everywhere but the ends is that is it bonds with some elasticity and will allow the bangle to be opened and closed without cracking. Super New Glue tends to be a bit more brittle when it is dry, and that is why we don't recommend it for the bendable part of the cuff, but will hold.
NO FREE SHIPPING
Your Price: $38.50
0 In Stock
Enter
Quantity
Average Rating0 Review(s)
20mm Glue-In Cuff Flat Leather Cord per 5 pieces - Shiny Gold
20mm Glue-In Cuff Flat Leather Cord per 5 pieces - Shiny Gold
24.5x3mm
Outer Diameter: 6 3/4 inches - start with 7 inch piece of cord and trim
Adjustable - will fit most wrist sizes
sold per bag
Brass Base Plated with Gold
Blank Base to glue in 20mm flat cord
Designer Tip: Each bangle takes one bracelet blank and 6 1/2 inches of 20mm leather or 13 inches of 10mm Leather cut into two 6 1/2 inch lengths or 26 inches of 5mm Leather cut into four 6 1/2 inch lengths. The bracelet blanks have rounded corners and the ends are at a slight angle. Using sharp scissors or flush cutters, trim one end of the leather to fit the bangle. Glue the end in with Super New Glue and use tape or wire to hold the leather in place while drying. Spread a small amount of E-6000 on the bracelet blank starting from the glued portion to about inch away from the other end. Press leather in place and trim other end to fit in bangle. Apply Super New Glue to the end of bangle and press leather in place, again using tape of wire to hold the leather while the glue is drying. A nail file can be used to smooth the rounded corners if desired. If the Super New Glue does not hold, allow it to dry completely and reapply. The rationale for using the E-6000 everywhere but the ends is that is it bonds with some elasticity and will allow the bangle to be opened and closed without cracking. Super New Glue tends to be a bit more brittle when it is dry, and that is why we don't recommend it for the bendable part of the cuff, but will hold.
NO FREE SHIPPING
Your Price: $38.50
0 In Stock
Enter
Quantity
Average Rating0 Review(s)
20mm Glue-In Cuff Flat Leather Cord per 5 pieces - Rhodium Plated
20mm Glue-In Cuff Flat Leather Cord per 5 pieces - Rhodium Plated
24.5x3mm
Outer Diameter: 6 3/4 inches - start with 7 inch piece of cord and trim
Adjustable - will fit most wrist sizes
sold per bag
Brass Base Plated with Rhodium
Blank Base to glue in 20mm flat cord
Designer Tip: Each bangle takes one bracelet blank and 6 1/2 inches of 20mm leather or 13 inches of 10mm Leather cut into two 6 1/2 inch lengths or 26 inches of 5mm Leather cut into four 6 1/2 inch lengths. The bracelet blanks have rounded corners and the ends are at a slight angle. Using sharp scissors or flush cutters, trim one end of the leather to fit the bangle. Glue the end in with Super New Glue and use tape or wire to hold the leather in place while drying. Spread a small amount of E-6000 on the bracelet blank starting from the glued portion to about inch away from the other end. Press leather in place and trim other end to fit in bangle. Apply Super New Glue to the end of bangle and press leather in place, again using tape of wire to hold the leather while the glue is drying. A nail file can be used to smooth the rounded corners if desired. If the Super New Glue does not hold, allow it to dry completely and reapply. The rationale for using the E-6000 everywhere but the ends is that is it bonds with some elasticity and will allow the bangle to be opened and closed without cracking. Super New Glue tends to be a bit more brittle when it is dry, and that is why we don't recommend it for the bendable part of the cuff, but will hold.
NO FREE SHIPPING
Your Price: $38.50
0 In Stock
Enter
Quantity
Average Rating0 Review(s)
20mm Glue-In Cuff Flat Leather Cord per 5 pieces - Rose Gold
20mm Glue-In Cuff Flat Leather Cord per 5 pieces - Rose Gold
24.5x3mm
Outer Diameter: 6 3/4 inches - start with 7 inch piece of cord and trim
Adjustable - will fit most wrist sizes
sold per bag
Brass Base Plated with rose gold
Blank Base to glue in 20mm flat cord
Designer Tip: Each bangle takes one bracelet blank and 6 1/2 inches of 20mm leather or 13 inches of 10mm Leather cut into two 6 1/2 inch lengths or 26 inches of 5mm Leather cut into four 6 1/2 inch lengths. The bracelet blanks have rounded corners and the ends are at a slight angle. Using sharp scissors or flush cutters, trim one end of the leather to fit the bangle. Glue the end in with Super New Glue and use tape or wire to hold the leather in place while drying. Spread a small amount of E-6000 on the bracelet blank starting from the glued portion to about inch away from the other end. Press leather in place and trim other end to fit in bangle. Apply Super New Glue to the end of bangle and press leather in place, again using tape of wire to hold the leather while the glue is drying. A nail file can be used to smooth the rounded corners if desired. If the Super New Glue does not hold, allow it to dry completely and reapply. The rationale for using the E-6000 everywhere but the ends is that is it bonds with some elasticity and will allow the bangle to be opened and closed without cracking. Super New Glue tends to be a bit more brittle when it is dry, and that is why we don't recommend it for the bendable part of the cuff, but will hold.
NO FREE SHIPPING
Your Price: $38.50
0 In Stock
Enter
Quantity
Average Rating0 Review(s)
Select Quantities